MANUAL AUTORIZACION BTP PDF

Zolokus Bring the Indexing flange along with manuaal disc, if it is not removed in proper angular position. Clamping bolts should be tightened after aligning the seating surface, square to the lathe axis. Bolt holes in the tool disc should tbp of extra large size to allow for angular adjustment. Referring to the signal diagram, value of T3 is particularly critical.

Author:Mera Voodookus
Country:Djibouti
Language:English (Spanish)
Genre:History
Published (Last):8 September 2004
Pages:215
PDF File Size:4.79 Mb
ePub File Size:15.83 Mb
ISBN:818-7-36204-431-3
Downloads:30408
Price:Free* [*Free Regsitration Required]
Uploader:Nishicage



Vikazahn In the clamped position of the turret, bolts 15 are in line with the holes drilled in flange Rotate motor shaft further two revolutions in same direction. It is also necessary for inspecting the clamping function of disc springs. Indexing cycle through manual tool demand will be identical to the normal indexing cycle, except for the fact the cycle will start even if initial signal conditions are not satisfied. It is a difficult task to remove such dowel pins, and to fit new ones.

Relatively small value components. Reference mark made on the coolant flanges 26 and 24 can serve as a rough guide. Even if turret clamping is not possible at this stage follow the mnual steps. Control should be capable of detecting the proximity switch signal within 3 to 6 ms. In such a case, tool position number, and encoder feedback will not match.

Actuation manjal the switch is indicated by built in LED light emitting diode. Coolant ring should then be shifted back and clamped in original position. Do not disconnect wiring. Referring to the signal diagram, value of T3 is particularly critical. Dowel Pins are not recommended for ensuring the alignment of turret. Take out the encoder For stopping the motor in minimum possible time, following measures are required: Remove rear cover Part Name Part No.

Motor contactor should be tripped without depending on PLC software. Remove proximity switchalong with its clamp Coolant ring should then be adjusted to align the coolant valve with the proper hole on the coolant flange ref. It is therefore, not possible to adjust the angular position of coolant ring by hand. First roughly position the slot in drive dog 23 in the same angular orientation as the pin 22 on the spindle. To release the nut, clamp the index gear assembly fig Adjustment of Ringfeder Clamps 26 Bring the Indexing flange along with tool disc, if it is not removed in proper angular position.

However, following general points should be noted while selecting the control system and its program: Clamping bolts should use machine washers of extra thickness min.

Assemble all the components 70, 71, 76 to 84 as shown in fig. Now place springs 11 and lock-nut 12 in position. The tool disc will then sit in an angular position, making it impossible to align the tools. In case turret clamping is not autorizacioon then rotate the motor shaft in whichever direction possible; in some manuual position bolts 15 will be in line with the holes in flange Coupling design allows the tool disc to be indexed without lifting. Partial Assembly of Spindle If the lift is less, it should be adjusted by grinding the bottom face of spring seat New dowels may involve enlarging the FIG 2.

Absolute position encoder gives feed-back of the turret position. Temps Unitaire en btp Documents. Assemble all components as shown in figure This will engage the pinion onto the gear teeth of the nut Put the lubricating oil Page One revolution of cam shaft completes one indexing inde xing cycle of declamp-index-clamp.

Check for free movement of sliding coupling rollers in drum cam groove. Mark a line on the nut face and spindle shaft to indicate the angular alignment. Tighten bolts 15 with a light force. Insert allen key in bolt head mwnual and tap it with hammer. Figure Bicycle Collisions and Parties at Fault Valve button continuously presses against coolant flange 26 fitted on indexing flange. Remove coolant flange 26 and coolant ring 24,1. Mechanical jam of the turret.

Most 10 Related.

GROVE GMK 5220 PDF

MANUAL AUTORIZACION BTP PDF

Vikora Follow the procedure given on page 14 to adjust the encoder in proper position. In this position, it is possible to turn the indexing flange 27 by hand. Assemble all the components 70, 71, 76 to atorizacion as shown in fig. It is then possible that valid encoder feedback is not available because the turret has stopped in an intermediate position. Such a condition is usually associated with the change in angular position of tool disc in the clamped position or excessive noise in one direction during indexing. Please follow step by step procedure autofizacion below: In such accidents, the friction joint of Ringfeder slips; and protects the internal mechanism from damage. Dark-faced Common Murres off California in falland winter.

EL AFINADOR DE PIANOS DANIEL MASON PDF

Vikazahn In the clamped position of the turret, bolts 15 are in line with the holes drilled in flange Rotate motor shaft further two revolutions in same direction. It is also necessary for inspecting the clamping function of disc springs. Indexing cycle through manual tool demand will be identical to the normal indexing cycle, except for the fact the cycle will start even if initial signal conditions are not satisfied. It is a difficult task to remove such dowel pins, and to fit new ones. Relatively small value components. Reference mark made on the coolant flanges 26 and 24 can serve as a rough guide. Even if turret clamping is not possible at this stage follow the mnual steps.

Related Articles